Marine Engine Parts

Shop Online

    Glenwood 4 Point Motor Mount
    Glenwood 4 Point Motor Mount

    4 Point Motor Mounts (Glenwood)
    These motor mounts are highly polished aluminum and will adapt to engine stringer spacing from 22” to 26”.Front & Rear motor mounts available for the following:

    #GLE 1292 “Front” Small Block Chevy $160.00
    #GLE 897 “Front” Big Block Chevy $180.00
    #GLE 900 “Front” Ford 429-460 $180.00
    #GLE 898 “Front” Oldsmobile 425-455 $180.00
    #GLE 914 “Rear” Small / Big Block Chevy $250.00
    #GLE 917 “Rear” Ford 429-460 $290.00
    #GLE 915 “Rear” Oldsmobile 425-455 $250.00
    Jet Boat Rail Kit

    Engine Mounting (Jet Boat Rail Kit)
    Made of Billet Aluminum and highly polished. These kits available both Chevy and Ford. They include front mount, rear mount, flywheel cover, drive shaft cover, 38” long engine rails, rail back – up plates, motor mounting blocks and stainless bolt kit. (Always remember to use Antiseize when assembling stainless nuts and bolts to prevent gulling.)
    #ARS Rail Kit Chevy $849.00
    #ARS Rail Kit Ford $849.00
     

    Individual Rail Parts
    454 Front mount $180.00
    Rear Mount 350-454chev $190.00
    Flywheel cover 350-454 chev $245.00
    Slotted Rails $180.00pr
    Rail Back-ups $110.00pr
    2" Mounting Blocks $35.00ea
    Drive shaft cover 7"oal $145.00

    Gasket Sealant Gasket Sealant
    4 oz. Gasket Sealing Compound $6.95
    Polished Bolt Kit Stainless Steel Engine Fastner Kit
    Stainless-steel hex cap bolt kit. Why use you rusty OEM bolts? Each kit includes: Intake manifold, valve cover, filler neck, timing cover, fuel pump, distributor hold-down, water pump, oil pan and header bolts. $39.99
    Thermostat (Kit)

    Thermostat Kit
    Does your boat engine run too cold? Maintain proper engine temperature (particularly in Jet Applications). Most engines are designed to run at a minimum of 160 degrees water temperature, for proper performance.
    #GLE 1800 $124.99
    “Not recommended” for use on Super Charged or Turbo Charged engines. Or engines running for long periods of time at maximum or near maximum power out put.

    Marine Thermostat

    Marine Thermostat
    High flow marine thermostats designed to help maintain constant temperature. Choose 160 degree or 180 degree. $21.95

    Cylinder Head Temperature Gauge Cylinder Head Temp Gauge
    Attaches directley to engine block. Reads cylinder head or block tempeture. 3/8" N.P.T. thread, 2.250" dia. $47.50
    Water Discharge Dividers

    Water Discharge Dividers (Cast Aluminum)
    Allows equal amounts of water to flow to exhaust manifolds or elbows.
    #GLE 0682 Chevy $27.99
    #GLE 0684 Olds $27.99
    #GLE 0683 Ford $27.99
    Thermostat Housings (Billet)

    Thermostat Housings
    (Billet Aluminum with O-ring gasket)
    #ARS 5510 Chevy Blower intake $54.99
    #ARS 5509 Chevy STD intake $54.99
    Water Cover Plate Polished Water Cover Plate
    Ideal for Jet boat applications.
    #GLE 0691 Oldsmobile $52.50
    #GLE 0693 Ford $52.50
    Water Cover Plate

    Water Cover Plates (Cast Aluminum)
    #GLE 0688 Small block Chevy $27.99
    #GLE 0692 Big Block Chevy $27.99
    Hose Barb

    Fittings (Chrome Plated)
    #1/2”NPT to 5/8” Hose barb (Straight) $6.99 each
    #1/2”NPT to 5/8” Hose barb (90’) $8.99 each

    Water Pressure Regulator

    Water Pressure Regulator (ARS Kit)
    Designed to prevent blown head gaskets or leaking solid copper head gaskets. Allows you to add up to 20’ degrees to your operating temperature. Maintains full water flow to engine, bypassing to a thru-transom fitting (hose not included) if pressure becomes excessive due to high RPM.
    #ARS Kit 126 $145.78
    Brass Ball Valve Brass Ball Valve
    Female X Female
    #MS-63280804 3/8" NPT $13.00
    #MS-63280812 1/2" NPT $15.00

    Male X Female
    #MS-08431017 1/2" NPT $15.00
    Liquid Filled Test Gauge Liquid Filled 2" Diameter Test Gauges.
    Stainless Steel Case.

    For use when checking Engine block pressure or checking Jet pump pressures.
    2" Dia 1/4"Npt bottom mount
    #MS-56469505 0-15 psi $21.85
    #MS-56469513 0-30 psi $17.85
    #MS-56469521 0-60 psi $17.85

    2" Dia 1/4"Npt back mount
    #MS-56469588 0-15 psi $22.85
    #MS-56469596 0-30 psi $18.85
    #MS-56469604 0-60 psi $18.85
    Fuel Pump Block Off

    Fuel Pump Block Off (Billet Aluminum)
    #ARS 5403 Small Block Chevy $15.99
    #ARS 5402 Big Block Chevy $15.99
    Carburetor Sacer Water Cooled Carburetor Spacer
    $44.99
    Carb Linkage Plate Carb Linkage Plate
    Fits under Holley 4150-4160 carbs. Includes 33c 6 hole cable clamp. $26.99
    Throttle Return Spring Kit Carb Mount Throttle Return Spring
    Bracket is Chrome plated steel, and mounts on carb stud for a clean look. Fits Holley 2300/4150/4160 Carburetors. $15.99
    Flame Arrestor

    Flame Arrestor (ARS Custom)
    These arrestors feature a high flow K&N filter element. The top and base are polished stainless steel. Arrestor/Air cleaner meets all US Coast Guard Requirements. They measure 10” Dia. X 3 ¾ Tall.
    #E 215-16 Standard Holley/Quadrajet $101.78
    #E 215-17 Holley Dominator $101.78
    #E 215-15F Replacement element only $41.00
    #E 215-1425 Optional Fuel Vent Tube $10.75
    #E 215-85-1362 Optional Breather Tube $16.95
    Engine Harness Engine Harness
    Wiring your boat's engine can be simple and easy. Take the frustration out of bad connections. These weather proof correct fit Hardin Marine engine harness make them the perfect choice for a new boat or to update an old boat. Save time and money. $119.99
    Mercruiser Cap and Rotor

    Cap & Rotor (Mercruiser)

    #MR---MMD300-03085
    Distributor Cap & Rotor for Thunder Bolt Ignition V8 $38.78
    Marine Spark Plug Wire Set

    Spark Plug Wire Sets (Marine)

    #MR--UIW102
    90’ Boots V-8 454,502,540,572 (HEI or Thunderbolt IGN) $50.00

    #MR--UIW110
    90’ Boots V-8 454,502,540,572 (Points style Mallory Stack Cap) $58.00

    #MR--UIW129
    90’ Boots V-8 454,502,540,572 (Mallory Flat Cap) $70.00

    Mallory Cap, Rotor, Points, and Condensor

    Cap , Rotor , Points & Condensor (Mallory)
    #MR—MI221B Flat cap V8 $45.65

    #MR—MI209D Conventional style $34.65

    #MR—MI319 Rotor Flat cap v8 $8.85

    #MR—MI309 Rotor Conventional style $8.85

    #MR---MI25042 Points $9.50

    #MR---MI400 Condenser $7.50

    Oil Pan Drain Kit

    Oil Pan (Drain Kit)
    #R 387-305-0380 ½ -20 drain plug $30.00
    #R 387-308-0380 12 mm drain plug $30.00
    Electric Oil Changer

    Electric 12v Oil Changer
    Heavy duty Jabsco pump, oil changer Bucket. 16qt bucket, 6’ power leads, with integral On/Off switch.
    #MR---J17800-2000 $167.00
    Utility Pump Handy Boy Utility Pump
    Versatile polished brass multi-purpose hand pump. Drain, fill or top up engine and gearbox oil Overcomes problem of hard to reach drain plugs and filler caps Oil and corrosion resistant brass neoprene construction with up to 1 1/2 gpm output 1001 other uses on any boat Fitting: Connection for 1/2" (13mm) ID hose Foot adapter for 1/2" (13mm) ID hose 2 each 1/2" (13mm) ID hoses 1 each 5/16" (6.5mm) probe, 1 each 1/4" (6mm) probe Size: 12" long x 1 1/4" diameter (31cm x 3cm) $68.99
    Fule Filter/Water Seperator

    Fuel Filter/Water Separators
    Replaces:
    Chris Craft 16.81-09746 OMC 502902
    Crusader 201104 Pleasure Craft RO77002
    Mercury 35-802885Q Yamaha YSC-10231-20-0c\

    #MR---18-7824 $7.00

    Big Block Chevy Sandwich Adapter Sandwich Adapter BBC
    Remote oil cooler sandwich adapters allow the use of a remote oil cooler while retaining the stock oil filter position. Machined from billet aluminum to provide strength, its black anodized for corrosion resistance, they bolt directly to the block and eliminate the factory bypass adapter. The filter then screws onto the bottom of the adapter, lowering it by 1 1/2". The adapters accept 1/2" NPT fittings and come complete with o-rings and fasteners. BB Chevy Mark IV $94.99
    Oil Cooler Heavy Duty Remote Mount Oil Cooler
    Chrome Plated

    Constructed out of high quality brass for optimum heat dissipation they have a 3" x 12" core. And feature 1" NPT water fitting ends & 1/2" NPT fittings for oil inlets and outlets.
    They measure 16" total length
    Brackets are included!
    #EOC-103P $399.85
     

    Click To Go To Homepage


    SITEMAP I TERMS AND CONDITIONSI CONTACT US

    Copyright© 2008 ARS MARINE INC - all rights reserved